User Login    
 + Register
  • Main navigation
Login
Username:

Password:


Lost Password?

Register now!
Fast Search
Slow Search
Google Ad


[Datsun 1200 encyclopedia]

B210 Tachometer

Revision as of 21:51, 18 June 2019; view current revision
<-Older revision | Newer revision->

Datsun 1200 encyclopedia | Recent changes | Edit this page | Page history | Switch to MediaWiki mode

Printable version | Disclaimers | Privacy policy | Current revision
Category: Datsun B210

Tachometer for Datsun B210.

Contents

Overview

Datsun B210 tachometer (24855-H5100)
24855-H5100.jpg

Datsun 720 tachometer (24855-03W00) vs Datsun B210 tachometer
06412d67.jpg

RHD vs LHD

The plastic box that contains it is the opposite way around. i.e, a mirror image.

Right-Hand Drive
15705.jpgAlbum 15705

Left-Hand Drive
B210_tachometer-face.jpg

One-Wire vs Two-Wire

A one wire tach has ONE black/white wire not two (it also has the red wire and black wire that plug into the instrument circuit board ). I think all RHD 120Y wiring harnesses expect a two-wire tach.

Possibly you can adapt it either by soldering another black/white wire onto the tach (there is a spot), or just putting t-intersection in where the black/white wires connect on your wiring harness so that the tach is connected and the ignition circuit is still closed.

One-wire LHD
12134.jpgAlbum 12134

Two-wire? LHD
Tachometer_B210_rear.jpg

LHD
12133.jpgAlbum click to view

LHD
Tachometer_B210_front.jpg

Wiring RHD

The tachometer is wired in series with the coil feed wire. There are two connectors that you pull apart behind the dash and connect the tach in the loop, plus it has an IGN+ wire.

RHD Wiring discussion
13528_4cc768929f4f8.jpgPost 343652

Wiring LHD

The tachometer is wired to the coil negative terminal. All North America (and perhaps all LHD) B210s have the tachometer wiring right there in the dash. So no cutting needed, and no new wires need to be run out to the coil.

6-pin connector with BW, B, R, RW and RB wires. One pin not connected. 
1976-1978 with the 6-pin connector
BW Coil-
B Ground
R IGN
1974
BW coil-
B to terminal 'A' on dash
R to terminal 'C' on dash 

The signal wire is brought into the dash wiring even if it didn't come with a tachometer originally.

1974: signal is a single wire in the dash harness
1976: 6-pin connector in the dash harness
1976 CALIFORNIA: signal wire comes from the electronic ignition black
     box (which is under the dash)

7484013842_2fe9d680e5_m.jpg 7484011750_0a6072c4f1_m.jpg 7484010102_010584da15_m.jpg 7484008332_69fd5f595d_m.jpg

LHD
B210_tach_a.jpg B210_tach_b.jpg

Tach-Volt Meter

174_5d095bf4bd3b5.jpgPost 491739

Part Numbers

TACHOMETER 1973-1975 
rectangle, 2-tab
  (op.) S-all (exc. 4-GX), Van
    24855-H5000 TACHOMETER
    24860-H5000 TACHO. VOLT METER
  S-all (exc. 4-GX), Van
    25007-H5000 MASK-tachometer
round, 2-tab
  24855-H5700 TACHOMETER GX
  24855-H5500 TACHOMETER (op.) K-DX, K-GL
  25007-H5500 MASK-tachometer K-DX 
¤