|
|
Re: FS: SYD - 1200 coupe diff complete |
|
Not too shy to talk  
Joined:
2005/5/27 7:48
From Canberra, Australia
Group:
Registered Users
|
Would the centre suit a H145.If so would you be prepared to seperate and ship the centre to canberra, i'm real desperate to replace the locker centre i have at the moment.
Cheers
tyrone.
Posted on: 2005/9/1 6:55
|
|
|
|
|
Easy Radiator Upgrade For 1000 ute A14 |
|
Not too shy to talk Joined:
2005/5/27 7:48
From Canberra, Australia
Group:
Registered Users
|
Trying to find out what is the simplest radiator upgrade for my 1000 ute running A14. There isn't much room to play with??
Cheers.
Posted on: 2005/8/19 3:11
|
|
|
|
|
Re: motor runs on, ignition off |
|
Not too shy to talk Joined:
2005/5/27 7:48
From Canberra, Australia
Group:
Registered Users
|
If you are using a stock carb they have a fuel cut-off solinoid ( spelling? ) attached to the carb that is meant to stop running-on. yours may be not working or connected properly..worth atry??
Posted on: 2005/7/22 4:37
|
|
|
|
|
Re: how much would you pay for tyres? |
|
Not too shy to talk Joined:
2005/5/27 7:48
From Canberra, Australia
Group:
Registered Users
|
In canberra re-treads are only illegal on V8 powered passenger vehicles. All 4's and 6's can use re-treads not matter what power they can put out. So you can run re-treads on your 300kw GTR skyline but not a stock 1968 v8 kingswood with maybe 150kw??
Posted on: 2005/7/22 4:28
|
|
|
|
|
Front Swaybar 1000 ute?? |
|
Not too shy to talk Joined:
2005/5/27 7:48
From Canberra, Australia
Group:
Registered Users
|
Anyone know if i can get a front swaybar for my 1000ute. Did datsun make one from factory or one from another datto that would suit?? Aftermarket whiteline or something??
Cheers- Tyrone ( trying to make my ute handle )
Posted on: 2005/7/19 4:56
|
|
|
|
|
Re: Again with the carby |
|
Not too shy to talk Joined:
2005/5/27 7:48
From Canberra, Australia
Group:
Registered Users
|
Had same problems witha 32/36 weber on my 180b - it would idle realy bad but run fine under load - Turned out to be a vacume leak where the carby mate's the inlet manifold. New gasket fixed the problem. worth a try??
Posted on: 2005/7/19 4:37
|
|
|
|
|
WTB: H145 diff centre ( A.C.T ) |
|
Not too shy to talk Joined:
2005/5/27 7:48
From Canberra, Australia
Group:
Registered Users
|
Chasing a free spinning H145 diff centre in Canberra A.C.T - Any Ratio - To replace my CIG locker shocker......
Cheer's
Tyrone.
Posted on: 2005/7/5 8:11
|
|
|
|
|
Re: 120y diff in 1000 ute |
|
Not too shy to talk Joined:
2005/5/27 7:48
From Canberra, Australia
Group:
Registered Users
|
Thanks Boofhead,
the modds required seem easyier to do than find a 1000 ute diff. The guards shouldn't be a problem as I'm running 13's and there's heaps of clearance. I have to get a tail shaft made up as I have fitted a dellow 5pd that will require a custom shaft.
Thanks again.
Tyrone
Posted on: 2005/7/5 8:05
|
|
|
|
|
120y diff in 1000 ute |
|
Not too shy to talk Joined:
2005/5/27 7:48
From Canberra, Australia
Group:
Registered Users
|
I am just wanting to conirm that this is possible( drum to drum )?? If so how much modification does it require... I have done a search and havn't been able to find an answer or I can't search properly??
Cheer's
Tyrone.
Posted on: 2005/7/5 7:12
|
|
|
|
|
Re: Dellow 5spd / A14 - What Clutch? |
|
Not too shy to talk Joined:
2005/5/27 7:48
From Canberra, Australia
Group:
Registered Users
|
Thnks mate, much appreciated..
Posted on: 2005/6/16 7:30
|
|
|
All Posts (ubu_nation)
Transfer
