|
|
Re: Pertronix Ignition problems |
|
Not too shy to talk 
Joined: 2005/6/27 6:07
From Carson City,NV USA
Group:
Registered Users
|
Connect red wire to + side of coil, connect both tach lead and black wire of pertronix to - side of coil. good luck.
Posted on: 2009/2/2 3:36
|
|
|
|
|
Re: U.S. crowd: Where can you get replacement strut inserts? |
|
Not too shy to talk 
Joined: 2005/6/27 6:07
From Carson City,NV USA
Group:
Registered Users
|
Hey,Sundat1200 try Monty @ Bits and Pieces.(562)420-3557 he's in SoCal and he supplies all us Datsun racers. He is a Koni distributor. Larry.
Posted on: 2007/4/25 1:58
|
|
|
|
|
Re: Flooding carbs |
|
Not too shy to talk 
Joined: 2005/6/27 6:07
From Carson City,NV USA
Group:
Registered Users
|
Hi, Dave your float valves could be hung open, or you might of had some sediment in the bottom of your float bowls and it is now plugging some of your jets.I would remove the float covers and check the float movement. Then remove the jets one at a time and blow them out with carb cleaner. That should help your problem or give you a good starting point as to whats not wrong with your carbs. Good luck Larry.
Posted on: 2006/7/23 23:42
|
|
|
|
|
Re: Drums Brake shoes Adjuster stuck |
|
Not too shy to talk 
Joined: 2005/6/27 6:07
From Carson City,NV USA
Group:
Registered Users
|
Try heating the aluminum body with a propane torch after using a good penatrating oil. Make sure you have the adjuster secured in a vice. Good luck Larry.
Posted on: 2006/7/22 20:18
|
|
|
|
|
Re: MSD for an A15 |
|
Not too shy to talk 
Joined: 2005/6/27 6:07
From Carson City,NV USA
Group:
Registered Users
|
Just use a datsun B-310 electronic dizzy,or convert the bluebird (610) or violet (710) dizzy to work with the msd box. Those dizzy's have a two wire magnetic hall effect switch that the msd box can read. Good luck, Larry
Posted on: 2006/7/7 3:02
|
|
|
|
|
Re: Clutch master cylinder compatability question |
|
Not too shy to talk 
Joined: 2005/6/27 6:07
From Carson City,NV USA
Group:
Registered Users
|
Gary, the simple answer is yes. You might have to adjust the push rod length or drill a new hole in the bracket on the push rod to get the pedal travel correct. Larry
Posted on: 2006/6/29 23:04
|
|
|
|
|
Re: Datsun USA owners: Where do you guys get your parts??? |
|
Not too shy to talk 
Joined: 2005/6/27 6:07
From Carson City,NV USA
Group:
Registered Users
|
Classic Datsun Motorsports is in Vista ,Ca. just north of San Diego. Les Cannaday is the owner and he has or can get any part for your car. Hell he even races a bad ass 1200 coupe, his phone # is (760)940-6365.
Posted on: 2006/6/15 2:56
|
|
|
|
|
Re: flares |
|
Not too shy to talk 
Joined: 2005/6/27 6:07
From Carson City,NV USA
Group:
Registered Users
|
Classic Datsun Motorsports phone # (760) 940-6365. Good luck with the flares.
Posted on: 2006/6/6 20:24
|
|
|
|
|
Re: Another glorious weekend at the track with my 1200 |
|
Not too shy to talk 
Joined: 2005/6/27 6:07
From Carson City,NV USA
Group:
Registered Users
|
Hey Rallytwit, did you run the new section of track that makes it a 3.1 miles. I'll be there on june 2nd-4th racing with Vara. I think Steve Smith introduced you to me a few years ago. I race a Datsun 510, orange/white/blue. You should come up and race that weekend or at least stop in for a cold beer. If you stop by look for a 240z BRE look alike and ask for Larry, hope to see you there.
Posted on: 2006/5/16 22:41
|
|
|
|
|
Re: question for RB engine gurus |
|
Not too shy to talk 
Joined: 2005/6/27 6:07
From Carson City,NV USA
Group:
Registered Users
|
Matt , you must not have been to many vintage races or scca events lately. Because I've seen more 240z at those events than I have at the drags. And I go to Irwindale and pomona for all the drag races/drag nites. My personal opinion is that you'll see more z's roadracing and autocrossing in california than you will dragracing.
Posted on: 2006/5/12 21:50
|
|
|