is he the guy from peders penrith or 2 different people???
how can i get a contact number you reckon???

if this peders still sell them il get them from them as its in drivable distance to save on postage
have you heard of the rest of these names listed???

are you springs reset???
is it lowered at all???
they look low to the ground

any idea who this kevin rowley is???
or number or something
apparently he sells lowered leafs brand new
theres a few other guys to i think
like peders in penrith or newcastle or something
ill find out some names asap

jts springs???

peders penrith???

john taylor???

kevin rowley???

any1 know if john taylor is peders penrith or are these all different???

phone numbers???

i did notice the reservior clossest to back is lower then the front and when i installed they were the same im pretty sure
i checked the reserviors and cant find any leaks i was hoping it was that or the clamp loose or something but no luck with any leaks around there

it sure is brand new
i bought it from a local BRAKE place...lol...
how could a seal go on a new master cylinder???
i double checked and it comes out between the master cylinder(bottom) and the plate on booster
not looking forward to pulling out and bleeding all over again

is there any way i could have stuffed it when installing
i cant imagine many ways i could have stuffed it appart from being faulty from factory but i would have thought the chances of that are very low but my luck spose the odds are there

if you work at aus post you should know that its perfectly normal to send something as small and light as a bellhousing
i have sent a few before and 1 went to qld
i have also sent and received alot bigger and heavier things with aus post such as
radiators
wheels
v8 extractors which are alot heavier and larger then a bellhousing

if ya boss said it cant be sent he or she is an idiot
and go to the next clossest aus post
but im 100% sure a bellhousing can be sent in a cardboard box as i have done a few times before

im looking at the aus post chart on my wall and it clearly states
19kg to 20 kg is the limit
it also says if its over this weight additional charges apply 1ce a price is agreed on
and the deemed weight(parcels volume incubic meters x 250 is also way under the limit
a bellhousing is no where near this weight and if it was you can still send it unless the post office refuses as they have the rite to refuse if over the limit
and even if that was the case you work at the post office so it wouldnt be an issue
but it could be double the size and double the weight and they and you would still not have the rite to refuse it as it would be well below the limit

i sell lots of things every week and never been refused esspecialy with something as small as a bellhousing

whorria
i have sent a bellhousing with australia post before to qld
its within the weight and size so you will have no problem at all sending it to qld

also slug 1200
i also have a c4 ready to go but the custom stall converter cost a fortune way more then the bellhousing to be made along with the special spigot bearing

how much did you pay to get it made???
and where from???

so its imposible for a good master cylinder to leak from
the bolt
and that plate between the booster and master

if i explain whats happening to the break place i hope they will replace it for me if thats the case

what a pain in the ass you wouldnt think a new product would be faulty

NOT HAPPY

i have a new master cylinder
new lines and fittings

it seems to be leaking either from or both
the plate that sits between master and booster i see fluid dripping from booster side of that plate

and the bottom bolt of the master cylinder

any ideas any1?????????????
any1 had this before??????????/

its a 120y booster/master cylinder setup

i noticed this when i was under the car and want to fix it but want a few ideas before i pull all appart cause its a pain in the ass

thanks

thanks mate please do cause i plan to make a similar setup using the caltracts set up hopefully using old 4link bars and pivot points cause i have the bars here so would make it easy just have to make plates to suit

so if you can post some good pics

thanks mate