Hi Guys

Yesterday i found My B310 was not pulling properly, engine hesitates felt like an ignition issue, Pulled the Distributor cap and rotar and found rotar had some black burn marks,
Sanded it and cleaned the rotor,cleaned the plugs and plug wires and distributor cap and contact point too and also re gapped them according to the B310 Manual

Spark Plugs 0.8-0.9 MM
Contact Point 0.45-o.55 MM
and installed them and started the car with choke fully closed position, it ran little better than yesterday but when the engine got hot it started to backfire horribly,
Checked the choke it was open completely
checked the carb float level it was perfect

what could be the issue ,is backfiring because contact point too low or too far ?
Check these Spark Plugs too
thanks
regards
sumith

Attach file:

---

  1.jpg (68.69 KB)


  2.jpg (66.42 KB)


  3.jpg (62.92 KB)

Hi DD

I think it is

thanks
regards
sumith

Hi DD

It is flowing to the Engine Compartment not to the passenger Compartment , Actually it looks it is leaking from the Plug seal It self not from the rubber hoses and connectors

thanks
regards
sumith

Hi Guys

I have a tiny water drop from my B310 Water return plug located on the dash board side, is there a anyway that i can fix that matter temporarily till i remove that plug and check it later,any glue or something like to fix it ? since i am going upcountry tour most probably this week end , it can run around 100 Km without refilling and heating it has A12A engine on it

thanks
regards
sumith

Attach file:

---

  5.jpg (49.41 KB)

Hi Guys

Look at this tyre, it says 175/60X13.5 so what is this rim size then ? there is no indication on it is it 13 or 14 or 13.5 ?

thanks
regards
sumith

Attach file:

---

  3.jpg (80.49 KB)


  4.jpg (87.87 KB)

Hi Guys

Look at this and what should be done to avoid this am i using different Shcoks or what is wrong here ? i think i would not be able to use higher rim size like 14, yet it will touch the shocks

thanks
regards
sumith

Attach file:

---

  1.jpg (69.17 KB)


  2.jpg (78.38 KB)

Hi Guys

The Tires i am running are much verse than these since i got them free just thought of finding a way to use ,ok might be i am mistaken i might have 13.5 Tyre on 14 Rims any way i have seen some 13.5 on the tire or rim i will confirm it by checking them ,
here it is it looks rim are wider the tyre is 13.5 low profile

thanks
regards
sumith

Attach file:

---

  tttt.JPG (52.35 KB)

Hi Guys

i got 4 13.5 Rim set that match my bolt pattern and also i got 4 used tyres of (165/70X14 Japanese Yokohama), will i be able to install them on my 13.5 Rims or do i need to buy 14 Size rims for them ? if so what model vehicle rim will be fine that uses rim size 14 ?

thanks
regards
sumith

Attach file:

---

  tyres.jpg (66.63 KB)

Hi SharmCos

Here are those the complete set up is not mine just the same thing i have
top pic is mine real ones and i got the same steering like the complete dash bottom snap here

thanks
regards
sumith

Attach file:

---

  Dash pannel.jpg (112.60 KB)


  GX Dash.jpg (78.13 KB)

Hi robbie

Here it is , Just has few putty work on edges and pannels little more , then i will probebly have a filler coat to hide them and then will be starting painting it,
most probably preparation work will be finished within this coming week end

thanks
regards
sumith

Attach file:

---

  car.jpg (63.13 KB)