User Login    
 + Register
  • Main navigation
Main Menu
Login
Username:

Password:


Lost Password?

Register now!
Fast Search
Slow Search

Advanced Search
Google Ad
   All Posts (lcw1980)




lcw1980
Re: Noob question valve clearance
#1
Just popping in
Joined:
2010/9/28 12:45
Group:
Registered Users
Posts: 19
Offline
@bakat: thats a good idea

Ok i'll try adjusting HOT nxt.

Posted on: 2011/8/12 15:09
Transfer the post to other applications Transfer


lcw1980
Re: Noob question valve clearance
#2
Just popping in
Joined:
2010/9/28 12:45
Group:
Registered Users
Posts: 19
Offline
Thanks. Much quieter now. Actually my feeler gauge doesn't have a .35mm one so i chose .25mm. On my first try i did not notice two feelers(.25 &.30) are stuck together and boy I panicked when the engine sounds like a broken sewing machine!

Posted on: 2011/8/11 17:11
Transfer the post to other applications Transfer


lcw1980
Noob question valve clearance
#3
Just popping in
Joined:
2010/9/28 12:45
Group:
Registered Users
Posts: 19
Offline
Hello again,

say mates i've read the valve clearance in wiki and it says it should be adjusted 0.013inch(0.25mm)COLD

But isnt 0.013inches=0.33mm? Just making sure you know...

Posted on: 2011/8/10 15:09
Transfer the post to other applications Transfer


lcw1980
Re: Electronic distributor
#4
Just popping in
Joined:
2010/9/28 12:45
Group:
Registered Users
Posts: 19
Offline
well bakat, based on what I've read abt ballast resistors and the input here, I'm quite sure I will keep my ballast resistor on my stock hitachi coil for the time being.

No offence. Thanks.

Posted on: 2010/11/26 5:51
Transfer the post to other applications Transfer


lcw1980
Re: Electronic distributor
#5
Just popping in
Joined:
2010/9/28 12:45
Group:
Registered Users
Posts: 19
Offline
oh one more thing, what qualifies as a high-energy coil??

Posted on: 2010/11/26 3:59
Transfer the post to other applications Transfer


lcw1980
Re: Electronic distributor
#6
Just popping in
Joined:
2010/9/28 12:45
Group:
Registered Users
Posts: 19
Offline
oh ok thanks.. coz the grease monkeys over here tells me to throw it away.. hmmm

Posted on: 2010/11/26 3:53
Transfer the post to other applications Transfer


lcw1980
Electronic distributor
#7
Just popping in
Joined:
2010/9/28 12:45
Group:
Registered Users
Posts: 19
Offline
I got myself a C22 vanette eletronic distributor for my A12. So my question is, do i need to remove the ballast resistor?

If I shouldnt remove it, then how should i wire it? directly to the coil terminals or in series with the resistor?

Posted on: 2010/11/26 2:15
Transfer the post to other applications Transfer


lcw1980
Re: A14 flywheel into A12
#8
Just popping in
Joined:
2010/9/28 12:45
Group:
Registered Users
Posts: 19
Offline
ok... I'll change it and see what happens *gulp*

Posted on: 2010/11/23 3:57
Transfer the post to other applications Transfer


lcw1980
Re: A14 flywheel into A12
#9
Just popping in
Joined:
2010/9/28 12:45
Group:
Registered Users
Posts: 19
Offline
So that means A14 flywheel can be fitted to A12 engine with no mods right?Quote:

LittleFireyOne wrote:
Yes you can fit it, you gotta check the flywheel bolts for premature binding before they're fully tight. I don't remember the specifics of it though, there's another thread around here that mentioned it in regaurds to A12 flywheel on larger A engines

Posted on: 2010/11/22 5:38
Transfer the post to other applications Transfer


lcw1980
A14 flywheel into A12
#10
Just popping in
Joined:
2010/9/28 12:45
Group:
Registered Users
Posts: 19
Offline
Ok i have a A12 b310 so....

Would it be possible to fit in a lightened A14 flywheel into A12 without any mods? Assuming the clutch and pressure plate is a A12 one? Thanks.

Posted on: 2010/11/22 3:35
Transfer the post to other applications Transfer



 Top
(1) 2 »