|
|
where sells body panels |
|
|
Just popping in
Joined:
2011/10/9 4:22
From Trinidad
Group:
Registered Users
|
Is there any where that sells replacement panels like rear fenders and hoods etc?
Posted on: 2012/4/13 1:55
|
|
|
|
|
Re: video of me in the datsun |
|
|
Just popping in
Joined:
2011/10/9 4:22
From Trinidad
Group:
Registered Users
|
The car has a welded diff..... I still have some issues with the car running rich, I'm now wondering if it's because I have a different turbo on it.. Any thoughts?
Posted on: 2012/1/4 0:05
|
|
|
|
|
video of me in the datsun |
|
|
Just popping in
Joined:
2011/10/9 4:22
From Trinidad
Group:
Registered Users
|
Posted on: 2012/1/2 16:04
Edited by ddgonzal on 2012/1/2 22:24:16
|
|
|
|
|
Re: how to wire ca18det |
|
|
Just popping in
Joined:
2011/10/9 4:22
From Trinidad
Group:
Registered Users
|
I have no clue how old the injectors are.... I doubt it'll be those though because all of the spark plugs are black and what are the odds that all of the injectors are faulty.... any other ideas?
Posted on: 2011/11/8 0:55
|
|
|
|
|
Re: how to wire ca18det |
|
|
Just popping in
Joined:
2011/10/9 4:22
From Trinidad
Group:
Registered Users
|
I checked the ecu for codes and it's clear.... I'll check the resistance at the ecu for the temp sender when I start it next.. just a quick question... how sensitive are these engine to fuel pressure? reason I ask is because I have an aeromotive fuel pressure regulator and have tried playing around with that to compensate for the rich condition by lowering the pressure to 20psi at idle with vacuum and roughly 28psi static
Posted on: 2011/10/31 14:35
|
|
|
|
|
Re: how to wire ca18det |
|
|
Just popping in
Joined:
2011/10/9 4:22
From Trinidad
Group:
Registered Users
|
I checked the coil pack for battery voltage.. good
I checked for continuity on ground circuit .... good
I removed all injectors and cleaned them .... doubt all 4 are leaking
changed the plugs again last night and the car ran like a beast for about half an hour and then started to run on 3 cylinders.. pulled all the plugs and all were black and fowled... any other advice? also someone was telling me that it could be the air flow sensor... I checked it against the factory service manual and it's within specifications ... running out of ideas here guys
Posted on: 2011/10/30 20:55
|
|
|
|
|
Re: how to wire ca18det |
|
|
Just popping in
Joined:
2011/10/9 4:22
From Trinidad
Group:
Registered Users
|
the throttle position sensor? no I didn't move it
Posted on: 2011/10/29 2:19
|
|
|
|
|
Re: how to wire ca18det |
|
|
Just popping in
Joined:
2011/10/9 4:22
From Trinidad
Group:
Registered Users
|
the engine starting but it is running really rich either that or the spark is weak. how to resolve this issue?
Posted on: 2011/10/27 23:46
|
|
|
|
|
how to wire ca18det |
|
|
Just popping in
Joined:
2011/10/9 4:22
From Trinidad
Group:
Registered Users
|
I have a ca18det in my datsun 1200 and wanted to know how to wire the ecu etc? I mean what colour wires from the harness goes to the ignition switch via a relay
Posted on: 2011/10/26 13:58
|
|
|
All Posts (mikeyr)
Transfer
