|
|
A14 engine diamensions? |
|
Just can't stay away  
Joined:
2013/6/13 1:29
Group:
Registered Users
|
Can anyone tell me a length width and height of an A14 engine?
I need to freight a stripped motor so I'm just trying to work out a rough price.
Thanks guys :)
Posted on: 2017/6/15 22:03
|
|
|
|
|
Re: 1200 Bonnet sitting lower than front guards. |
|
Just can't stay away Joined:
2013/6/13 1:29
Group:
Registered Users
|
Thanks guys will take another look in the morning.
Posted on: 2017/3/5 10:08
|
|
|
|
|
Re: 1200 Bonnet sitting lower than front guards. |
|
Just can't stay away Joined:
2013/6/13 1:29
Group:
Registered Users
|
Hey mate.
Looks like it latches far too low.
With the bonnet sitting on these rubbers it doesn't latch the bonnet closed.
Could there be a problem with the mechanism.... does it have an adjusting screw or something ? Or could it be that the guards are on too high....
I know the previous owners took off every panel for paint and there's a few things that arnt straight .
Posted on: 2017/3/5 3:11
|
|
|
|
|
Re: 1200 Bonnet sitting lower than front guards. |
|
Just can't stay away Joined:
2013/6/13 1:29
Group:
Registered Users
|
Awesome :) thanks mate.
Posted on: 2017/3/4 7:41
|
|
|
|
|
1200 Bonnet sitting lower than front guards. |
|
Just can't stay away Joined:
2013/6/13 1:29
Group:
Registered Users
|
Anyone had this problem?
Where was the problem found?
Cheers :)
Posted on: 2017/3/4 7:27
|
|
|
|
|
Accelerator cable!! |
|
Just can't stay away Joined:
2013/6/13 1:29
Group:
Registered Users
|
Can anyone tell me if there is an accelerator cable from a modern car that I would be able to buy off the shelf at Repco or Supercheep today that would fit my 1200 ute?
Thanks. :)
Posted on: 2016/10/16 1:08
|
|
|
|
|
Re: A12 flywheel on A15 with 56A gearbox? |
|
Just can't stay away Joined:
2013/6/13 1:29
Group:
Registered Users
|
Hey... I've adjusted the free play to around 12mm but is there any way to adjust the cable at the transmission?
I'm not sure if it is correct...
There's a little bit of play but I'm not sure if it is play as I'm comparing the amount of pressure needed to move it to that of the clutch pedal... Is it harder to move the arm on the gbox than it is to push the pedal....
Also... Does free play at the arm mean the cable travel before it pulls the arm or how much the arm moves with not a lot of force required.
Cheers.
Posted on: 2016/9/24 2:58
|
|
|
|
|
Re: A12 flywheel on A15 with 56A gearbox? |
|
Just can't stay away Joined:
2013/6/13 1:29
Group:
Registered Users
|
So the combo is correct... Doesn't grind into reverse or any other gear when stationary...
Could pedal free play be the reason it has a bang out of the gearbox when releasing the clutch to take off in first?
Posted on: 2016/9/20 9:21
|
|
|
|
|
Re: A12 flywheel on A15 with 56A gearbox? |
|
Just can't stay away Joined:
2013/6/13 1:29
Group:
Registered Users
|
So I have a 120mm pad height...
I'll test what you just told me.
Posted on: 2016/9/20 9:16
|
|
|
|
|
Re: A12 flywheel on A15 with 56A gearbox? |
|
Just can't stay away Joined:
2013/6/13 1:29
Group:
Registered Users
|
Okay so transmission has 3-4mm
So pedal has about 40mm of free play :/
also do I measure pad height from the floor pan starts to rise up towards the dash?
Posted on: 2016/9/20 9:06
|
|
|
All Posts (brodiet2)
Transfer
