|
|
Re: WTB: s13 front brake adaptor |
|
No life (a.k.a. DattoMaster)
Joined: 2004/10/13 6:13
From penrith,sydney,aus
Group:
Registered Users
|
Not sure how much postage would be mate, I'm not using them because I want to run 13in steelies with hubcaps
Posted on: 2015/11/25 8:09
|
_________________
2 door 1200 sedan project l20b stroker
|
|
Re: WTB: s13 front brake adaptor |
|
No life (a.k.a. DattoMaster)
Joined: 2004/10/13 6:13
From penrith,sydney,aus
Group:
Registered Users
|
I got a complete setup minus hubs if you are interested, 280mm disc, completely rebuilt calipers and caliper brackets, asking 250 located in blue mountains
Posted on: 2015/11/24 21:31
|
_________________
2 door 1200 sedan project l20b stroker
|
|
Re: WTB Wheels Sydney |
|
No life (a.k.a. DattoMaster)
Joined: 2004/10/13 6:13
From penrith,sydney,aus
Group:
Registered Users
|
I got a set of freshly painted Trx rims with new tyres on the front and about 90% tyres on the rear , will also throw in 2 more 90% tyres for $250
Posted on: 2015/6/30 0:16
|
_________________
2 door 1200 sedan project l20b stroker
|
|
wtb:250mm s13 rotor and calipers |
|
No life (a.k.a. DattoMaster)
Joined: 2004/10/13 6:13
From penrith,sydney,aus
Group:
Registered Users
|
After a set of rotor and calipers , 250mm s13 preferred, located sydney
Posted on: 2014/7/17 1:34
|
_________________
2 door 1200 sedan project l20b stroker
|
|
Re: a12 overfueling |
|
No life (a.k.a. DattoMaster)
Joined: 2004/10/13 6:13
From penrith,sydney,aus
Group:
Registered Users
|
Float seams to be touching it but not completely pushing the nipple in , but once the float is back in the fuel and floating it should be pushing it right up right?, I'm stuck
Posted on: 2014/4/27 6:42
|
_________________
2 door 1200 sedan project l20b stroker
|
|
a12 overfueling |
|
No life (a.k.a. DattoMaster)
Joined: 2004/10/13 6:13
From penrith,sydney,aus
Group:
Registered Users
|
Hey guys, I just brought a 1200 wagon stocker and it seems to be running pretty crap, I've replaced the plugs and done the timing but seems to be more a fuel problem, the motor has been rebuilt and the carby has had a kit put through it, the fuel window on the front of the carby is as full as it can get and from my reading it needs to be within 1mm of the centre of the window, I've adjusted the float back to factory clearances and it's still full, any ideas as I'm no good with carbys after always having dattos with engine conversions I've never had to work on a carby Cheers
Posted on: 2014/4/27 0:00
|
_________________
2 door 1200 sedan project l20b stroker
|
|
Re: wtb 1200 lowered front springs and 3in blocks |
|
No life (a.k.a. DattoMaster)
Joined: 2004/10/13 6:13
From penrith,sydney,aus
Group:
Registered Users
|
All good, just got some off datgx, thanks anyways
Posted on: 2014/4/22 11:15
|
_________________
2 door 1200 sedan project l20b stroker
|
|
wtb 1200 lowered front springs and 3in blocks |
|
No life (a.k.a. DattoMaster)
Joined: 2004/10/13 6:13
From penrith,sydney,aus
Group:
Registered Users
|
I'm chasing a set of lowered springs and 3in blocks (or close) for my 1200, I'm located in Penrith but will pay postage if needed, also after some 13in Stockies preferably with tyres
Posted on: 2014/4/22 6:55
|
_________________
2 door 1200 sedan project l20b stroker
|
|
wtb 79 sunny diff center |
|
No life (a.k.a. DattoMaster)
Joined: 2004/10/13 6:13
From penrith,sydney,aus
Group:
Registered Users
|
I'm chasing a 79 sunny diff center, I'm located in Penrith nsw so closer the better, will pay for postage if needed though Cheers
Posted on: 2014/4/8 1:06
|
_________________
2 door 1200 sedan project l20b stroker
|
|
Re: Motor Swap |
|
No life (a.k.a. DattoMaster)
Joined: 2004/10/13 6:13
From penrith,sydney,aus
Group:
Registered Users
|
You can fit a ca box in a standard manual tunnel if you make your engine xmember to suit, seen it done, but overall a tunnel isn't hard to do anyway
Posted on: 2014/3/11 4:23
|
_________________
2 door 1200 sedan project l20b stroker
|
|