Hi DD

I have added a pic of it
is this specific to a different model is there any advantage or disadvantage on this type of Propeller shaft ?

thanks
regards
sumith

Hi Guys

Put rust killer under dash and sanded the area and applied a oil primer hand coat including the roof

thanks
regards
sumith

Attach file:

---

  DSC00279.JPG (100.70 KB)


  DSC00280.JPG (97.07 KB)


  DSC00283.JPG (97.81 KB)


  DSC00284.JPG (79.13 KB)

two piece shaft is weird,car is coming along nice bet them fingers were sore for a bit there.i hate sanding.

Hi Guys

Few Pic Updates


thanks
regards
sumith

Attach file:

---

  DSC00322.JPG (114.81 KB)


  DSC00323.JPG (115.02 KB)


  DSC00324.JPG (105.78 KB)


  DSC00325.JPG (122.67 KB)


  DSC00329.JPG (110.06 KB)


  DSC00345.JPG (60.41 KB)

Hi Guys

Just got 2 free days after new year festival days, could make a chassis line and and tagged a single side flow board, it was extremely difficult to
make chassis line strong enough to keep the flow board steady since it was a one side chassis line under the flow board made some spot welding to make it stronger
so the outer look of it is ugly to me still can hide them with a flour paint code. and also managed to remove rusted roof area and fabricate a new steel plate and the battery box too..

thanks
regards
sumith

Attach file:

---

  DSC00001.JPG (84.82 KB)


  DSC00005.JPG (87.63 KB)


  DSC00008.JPG (111.30 KB)


  DSC00010.JPG (99.50 KB)


  DSC00011.JPG (99.54 KB)

Hi Guys

Since newly welded part tend to get corrosion put and oil primer coat on them to avoid rust them again, and also removed
fender part to weld new steel plate there since it has been corroded and lot of body filler on this area.

manged to take a snap on little fellow on it , he is worried about this more than me always plays with it .
Even if i can't drive it he is able to drive it

Attach file:

---

  DSC00030.JPG (109.06 KB)


  DSC00085.JPG (122.58 KB)


  DSC00084.JPG (124.61 KB)


  DSC00029.JPG (95.38 KB)


  DSC00027.JPG (97.11 KB)

Hi Guys

Could finish carriage area last week

thanks
regards
sumith

Attach file:

---

  DSC00110.JPG (75.73 KB)


  DSC00113.JPG (71.98 KB)


  DSC00114.JPG (70.30 KB)

coming along nicely.

Hi Guys

Few Updates on my Project for last week end

thanks
regards
sumith

Attach file:

---

  DSC00047.JPG (102.02 KB)


  DSC00048.JPG (113.30 KB)


  DSC00049.JPG (129.12 KB)


  DSC00050.JPG (108.27 KB)


  DSC00051.JPG (122.88 KB)


  DSC00052.JPG (125.75 KB)


  DSC00053.JPG (126.44 KB)

Hi Guys

Few updates on wheel arch behind and seat holder on driving seat

thanks
regards
sumith

Attach file:

---

  DSC00056.JPG (120.21 KB)


  DSC00058.JPG (106.98 KB)


  DSC00060.JPG (114.71 KB)


  DSC00061.JPG (114.18 KB)


  DSC00063.JPG (112.31 KB)