mate i pm'd about some parts but no reply??

Make me an offer if you are interested, the price is a stab in the dark at the moment.
Will look at selling EFI manifold, turbo setup and head as a lot and the A14 stuff seperately. The head is no use to me as it is a low comp H75 and been modified to suit the EFI manifold.

OK, pulled the head off and it is a ported H75, with double valve springs (springs have some surface rust from sitting) and polished chambers/valves. No. 3 plug will prob need a helicoil as plug was pretty tight coming out. Looks like head has never been used since all the work was done.
Short block has some light surface rust in bores, might clean up with some wet and dry but prob best to give it a quick hone.
Will put a few more pics in the site album, just search for them by looking in my profile.

Looking for offers around $1200 for all the drivetrain except diff/driveshaft. Take the lot, EFI manifold, turbo and manifold (+ crossmember and mounts), ported H75 head, assembled short block, bare block, crank, pistons and rods, ancillaries, ribbed case 4 speed, radiator (late model, wide and low).

Want to get rid of it as a lot as can't be bothered with shifting it bit by bit. Will seperate if a couple of people want to split the gear up but it's all gotta go!

Call 0407 118 698 or PM etc..

OK, will try and list what there is available..

Low mount turbo setup, includes:
Tubular manifold
T25 turbo from RB20, unknown condition but spins OK, some radial play.
Old pod type uni filter
Start of dump pipe, needs wastegate pocket finished and exhaust
Water hoses
Start of oil supply line
1200 cross member with custom mounts to allow turbo to sit low

Sunny EFI manifold
Has had some alloy welding in places i.e. head face, needs porting to match oval port again, can’t see any obvious cracks etc.
Unknown non-standard TB, some minor porting required to match manifold
New fuel rail with flowed? FJ20 injectors

Ported oval port head
Unknown CR, will be pulling it off to check and can also measure valves then too.
Has small notches in top face of port to suit the EFI manifold injector bosses
Valve springs unknown, will update when remove head.
Has AN type fitting in one of the sender bosses for turbo water supply

A14 short block
Standard, unknown condition, will be able to check bores when I remove head
Rotates by hand OK
Has AN type fitting on waterpump suction pipe (one that the bottom radiator hose connects to) for turbo water return
Sump has oil return hose welded into it
Clutch sposed to be button puck type but will clarify when removed

A14 bare block
Possibly bored and honed, still has grease in bores to protect from rust
Sump has oil return welded into it
Otherwise condition unknown

A14 rotating assy
Bare crank, has some rust from sitting in car unprotected
Various piston and rod sets in various states of assy, and condition

4 spd gearbox
picking it is 56 series but will confirm when removed, unknown condition

Lights
All lights OK
Taillight surrounds have been painted but paint is peeling off OK, should be recoverable to std condition.

Bumpers/Grille/Chrome/Glass
Bumpers have been painted but again should come off to reveal chrome, look in good condition with no dents but need to remove paint to confirm
Grille painted black, in good condition otherwise
All chrome there apart from the bits I need
Glass all there apart from front screen

Interior
Door and rear ¼ cards trimmed in black cloth/carpet, speaker holes in rear ¼’s, good condition otherwise
Hood lining sprayed black, think there is a tear but will confirm
No seats
Center console has small 50mm gauge in it
Dash cracked with carpet mat over it
Gauge cluster painted black? All controls still there
Unknown sports steering wheel, avg condition
Black aftermarket carpet, avg condition, prob be OK with good clean
Various interior parts, handbrake, door handles, pedals etc
Plastic trim for boot area looks OK but need to confirm

Body
Doors look good but have been painted so not sure on bog etc, can magnet test if wanted
Boot lid has small dent in lower RHS, otherwise OK
Fuel tank

Would prefer to do the drivetrain etc as a package but will look at splitting. Any questions give me a call on 0407 118 698, PM or post away.. Will happily post pics IF I can figure out how to do so properly, I just want them to show in the post, hate clicking through to links..

Yes, was on ebay recently.

Is this the coupe that was on ebay recently ?

OK still not sure about posting pics but couple in the engine album of the turbo manifold set up:

http://datsun1200.com/modules/myalbum/photo.php?lid=21765

http://datsun1200.com/modules/myalbum/photo.php?lid=21764

Will put up more pics and details this weekend when I get the time to sort through everything.

OK, photobucket doesn't work??

Any hosting services work or do I need a album?

Pics didn't work..

pic of the low mount turbo manifold please?