Browsing this Thread:
1 Anonymous Users
|
Re: 1200 coupe project |
|
Just can't stay away
Joined: 2011/7/20 10:10
From central qld
Group:
Registered Users
|
Some photos of diff fitted after been shortened. Still waiting on the forged axles to turn up to fit and can't wait pretty excited to see how they look and fit.
Still will need to get leafs reset virtually flat to lower a lot more. Like the look of tyres tucked under guards. These are only small 225/50/15 as fit the 15x6.5 ford rims nice.
Posted on: 2017/4/12 4:23
|
|
|
Re: 1200 coupe project |
|
Just can't stay away
Joined: 2011/7/20 10:10
From central qld
Group:
Registered Users
|
Some pics of engine crossmember to suit ca18 engine, engine mounts are cheap eBay cortina mounts. All the steering gear is stanza stuff. Should be bit better than stock.
Posted on: 2017/4/12 4:27
|
|
|
Re: 1200 coupe project |
|
Just can't stay away
Joined: 2011/7/20 10:10
From central qld
Group:
Registered Users
|
Working on the tunnel, need to do a lot more but for now I just cut it out roughly to allow ca18 with 4 speed auto to fit. Will looking into it more when get to it but that tunnel was one I fitted to a ke20 I had but cut back out of Rolla and went a lot bigger as changed from a jatco 3 speed to the 4 speed (re4ro1a) and a lot bigger so just using this one to roughly work out where to cut my datto to suit, I will get a bigger one rolled in future to weld in. A lot of room around box is always a good thing fitting box and doing general work on it. I never had a small turbo car with auto before so all new to me but really keen to get this one going to see how good it is and getting older now and hate pushing a clutch in these days, I have fitted a manual valve body to the auto and running a b&m pro ratchet shifter got a good combo just need to put it all together and have fun
Attach file: IMG_5152.JPG (47.81 KB)
Posted on: 2017/4/12 4:37
|
|
|
Re: 1200 coupe project |
|
Just can't stay away
Joined: 2011/7/20 10:10
From central qld
Group:
Registered Users
|
Woohoo axles turned up from atracingworld and bloody awesome, a must if going shorter custom axles for bw78 or 9inch diff. Will fit these over weekend
Attach file: IMG_5155.JPG (47.93 KB)
Posted on: 2017/4/13 6:59
|
|
|
Re: 1200 coupe project |
|
Just can't stay away
Joined: 2011/7/20 10:10
From central qld
Group:
Registered Users
|
So I've done some more finally. Been busy life buying and setting up new house but let's remember how to post photos again
Posted on: 2020/3/26 8:47
|
|
|
Re: 1200 coupe project |
|
Just can't stay away
Joined: 2011/7/20 10:10
From central qld
Group:
Registered Users
|
So running 5 stud front setup. Chopped these 180b struts and fitted a coilover kit.
Attach file: IMG_5492_resize_51_compress30.jpg (105.33 KB)
Posted on: 2020/3/26 9:31
|
|
|
Re: 1200 coupe project |
|
Just can't stay away
Joined: 2011/7/20 10:10
From central qld
Group:
Registered Users
|
Brakes I've got some old vl turbo single piston and they got the cooling fins all over them, I guess that's how you tell. They have a 3inch bolt spacing which bolt straight onto my struts and i machined the rotor down 5mm and just run 6mm washers to space out caliper centre on rotor. I had some 4 inch rim blanks so cut the centres out of some ford pursuit rims and welded these together so they will fit inside front guards.
Posted on: 2020/3/26 9:37
|
|
|
Re: 1200 coupe project |
|
Just can't stay away
Joined: 2011/7/20 10:10
From central qld
Group:
Registered Users
|
Found this old as rn25 or so 1970something hilux diff and cost bugger all so chopped it and made it suit. I like the clean look of drum brakes and the clean housing look. I narrowed it to suit 15x8 0 offset 235/60/15 m/t tyres.
Posted on: 2020/3/26 9:42
|
|
|
Re: 1200 coupe project |
|
Just can't stay away
Joined: 2011/7/20 10:10
From central qld
Group:
Registered Users
|
Good to see it on wheels again been along time
Attach file: 20200222_173625_resize_94_compress85.jpg (144.89 KB)
Posted on: 2020/3/26 9:45
|
|
|
Re: 1200 coupe project |
|
Just can't stay away
Joined: 2011/7/20 10:10
From central qld
Group:
Registered Users
|
Ended up buying this old school radiator intercooler setup that looked neat and alot cheaper than buying other stuff but with 16fan all mounted it sits way too close to engine so thinking about moving engine back which will need the firewall recessed abit
Posted on: 2020/3/26 9:50
|
|
You can view topic.
You cannot start a new topic.
You cannot reply to posts.
You cannot edit your posts.
You cannot delete your posts.
You cannot add new polls.
You cannot vote in polls.
You cannot attach files to posts.
You cannot post without approval.