|
|
Browsing this Thread:
1 Anonymous Users
|
|
Re: strut brace for 1200 where 2 find |
|
No life (a.k.a. DattoMaster)  
Joined:
2004/5/4 8:32
From Canberra
Group:
Registered Users
|
I'll get a tri-bar, but I'm not sure in strut tower-firewall distance is the same for 1200s and 120Ys?
Posted on: 2007/5/15 13:07
|
|
_________________
Recommend trading with: gx5, wardat, dat141, datwags, boofhead, PIGDOG, MYORGZM, sssute, Ronald, beattie, dodgeman, dog160, LAGWAGON, Whitesedan, DamienS, simmos_datto, Team
|
|
|
Re: strut brace for 1200 where 2 find |
|
Home away from home  
Joined:
2006/2/1 12:47
From Adelaide
Group:
Registered Users
|
Yes, i was going to make one for my car, as i wasn't shore wether any one would want to go to the extent for themselves. If there is intrest i will make more of them.
Posted on: 2007/5/15 11:25
|
|
|
|
|
Re: strut brace for 1200 where 2 find |
|
No life (a.k.a. DattoMaster) 
Joined:
2001/1/30 1:33
From California
Group:
Registered Users
|
sssute, you're making alloy tri-bars?
Posted on: 2007/5/15 11:20
|
|
|
|
|
Re: strut brace for 1200 where 2 find |
|
Home away from home Joined:
2006/2/1 12:47
From Adelaide
Group:
Registered Users
|
boofhead, yes the end plates are different, i'm not getting the holes laser cut, i'll drill them using a jig i made after.
The upstands i'm making are up a bit higher so a straight bar clears the ca in my car, i have to test it to see if it will clear other motors. If not i have access to a bender, so should be able to make them work with most combos.
Posted on: 2007/5/15 6:03
|
|
|
|
|
Re: strut brace for 1200 where 2 find |
|
Home away from home 
Joined:
2004/4/10 18:48
From In front, and pulling away.Sometimes around Sydney....ish!
Group:
Registered Users
|
Put my name down for one.
Posted on: 2007/5/14 20:42
|
_________________
Lifes good when your on BOOST! 
|
|
|
Re: strut brace for 1200 where 2 find |
|
No life (a.k.a. DattoMaster) 
Joined:
2004/2/10 1:59
From torquay, victoooooria, australia
Group:
Registered Users
|
i looked at doing them for 1600's when i did mine but you need to make up 2 different end plates as the strut top bolt orientation is rotated 180deg between the 1200/120ys and the 1600
edit : also if you can spin the bar when it's in place are you looking at using a straight bar between the towers ?? cos there'll be clearance problems over the CA's SR's and Aseries with big air filter assemblies ...
Posted on: 2007/5/14 20:38
|
|
_________________
My Datsun is small and turns corners fast ....
|
|
|
Re: strut brace for 1200 where 2 find |
|
Home away from home Joined:
2006/2/1 12:47
From Adelaide
Group:
Registered Users
|
Im making up 15 sets, to suit 1200, 120y, 1600. Price im not sure yet, still waiting on a price for machining of the ally rod. They are having left and right threded rose joints, so that they can be set without un-bolting.
Posted on: 2007/5/14 20:34
|
|
|
|
|
Re: strut brace for 1200 where 2 find |
|
Home away from home 
Joined:
2006/2/27 21:36
From southern sydney "the shire"
Group:
Registered Users
|
Quote: Im making some at the moment, they should not be to far away. They will have steel end plates, and ally center rod with rose joint ends. They are at the laser cutters at the moment. How many are you making? How much?
Posted on: 2007/5/14 20:10
|
|
|
|
|
Re: strut brace for 1200 where 2 find |
|
No life (a.k.a. DattoMaster) Joined:
2004/5/4 8:32
From Canberra
Group:
Registered Users
|
I'll be up for one
Posted on: 2007/5/14 15:54
|
|
_________________
Recommend trading with: gx5, wardat, dat141, datwags, boofhead, PIGDOG, MYORGZM, sssute, Ronald, beattie, dodgeman, dog160, LAGWAGON, Whitesedan, DamienS, simmos_datto, Team
|
|
|
Re: strut brace for 1200 where 2 find |
|
Home away from home Joined:
2006/2/1 12:47
From Adelaide
Group:
Registered Users
|
Im making some at the moment, they should not be to far away. They will have steel end plates, and ally center rod with rose joint ends. They are at the laser cutters at the moment.
Posted on: 2007/5/14 15:45
|
|
|
You can view topic.
You cannot start a new topic.
You cannot reply to posts.
You cannot edit your posts.
You cannot delete your posts.
You cannot add new polls.
You cannot vote in polls.
You cannot attach files to posts.
You cannot post without approval.
|
Transfer
